LMCorse / Product support

LM-Dash
Manuals & support.

Find an answer, browse the documentation or follow a recovery procedure for your dashboard.

Find an answer

How can we help?

Search by symptom, message or feature. Open any question to view the answer.

Getting startedHow do I open the Setup menu?

Stop the car and engage the handbrake. From a screen other than Race, press and hold the original button on the right side of the steering column until Setup opens.

Source: Quick installation guide; Odometer Reset Manual v2

Getting startedWhich button controls LM-Dash?

Use the original Lotus button on the right side of the steering column.

In non-racing themes, a short press changes the theme and a long press resets the trip. In racing themes, a short press starts or stops lap timing; the first long press resets race data and the second long press changes the theme.

Source: LM-Dash FAQ

Getting startedIs LM-Dash plug and play with my car?

On supported models, LM-Dash replaces the original dashboard using the original vehicle connectors. Confirm the exact vehicle, model year and LM-Dash version with LMCorse before installation. The MY04 installation also uses a CAN bus connector.

Record the original mileage before removing the cluster and follow the installation guide for your version.

Source: Quick installation guide; FAQ notes

Getting startedWhat do I need to enter at first startup?

Accept the terms of use, select metric or imperial units, enter the correct total distance recorded from your original dashboard, set the date and time, then select Save and Exit.

Check the mileage carefully before confirming. If you enter it incorrectly, contact LMCorse.

Source: Quick installation guide; LM-Dash FAQ

Getting startedCan I use kilometres or miles?

Yes. Select metric (km/h) or imperial (mph) units during initial setup. The FAQ notes also describe changing the measurement units in Setup.

Source: Quick installation guide; FAQ notes

TroubleshootingLM-Dash will not turn on. What should I check?

Check the vehicle battery charge and confirm that the installed LM-Dash version matches your car and model year. The installation guide identifies low battery voltage and an incorrect dashboard version as possible causes.

If the issue continues, contact LMCorse with your vehicle details and LM-Dash version.

Source: Quick installation guide

TroubleshootingThe dashboard freezes when I start the engine.

Low battery voltage or high starter current consumption can freeze the startup screen. Check the battery charge. The installation guide describes waiting a few seconds for the emergency startup procedure, which opens the Progressive theme.

If it does not recover, contact LMCorse before attempting a software restore.

Source: Quick installation guide

TroubleshootingI cannot enter Setup because the handbrake signal is not detected.

The installation guide gives an alternative entry method: quickly press the letter “S” in the LM Corse logo shown on the startup screen.

Keep the vehicle stationary and contact LMCorse if the handbrake signal remains incorrect.

Source: Quick installation guide

TroubleshootingSpeed and RPM are missing. What should I check?

For transitional 2010/2011 cars, the installed electronics may correspond to MY08. The FAQ notes recommend checking the model-year setting in Setup and selecting the version matching the actual vehicle electronics.

Confirm the correct selection with LMCorse if you are unsure.

Source: FAQ notes

TroubleshootingWhere is the physical reset button?

The reset button is inside the small hole to the left of the screen. The FAQ describes using a thin tip, such as a paper clip, to press it when the display freezes or the device repeatedly reboots.

If an update is still progressing, let it finish. For a failed update, follow the matching recovery answer below.

Source: LM-Dash FAQ; LMCorse firmware recovery instructions

Wi-Fi & updatesHow do I connect LM-Dash to Wi-Fi?

Enter Setup → Settings → Wi-Fi → Connect, select or enter your network, enter its password and save/confirm. A successful connection shows the network/IP information in the upper-right corner.

Some firmware versions place Wi-Fi under Advanced. Use Connect to select a network rather than only switching Wi-Fi on or off.

Source: LM-Dash FAQ; FAQ notes

Wi-Fi & updatesHow do I update the firmware?
  1. Enter Setup.
  2. Settings.
  3. Wi-Fi → Connect: enter or choose your Wi-Fi network and save.
  4. Go back to Advanced.
  5. Firmware.
  6. LMDash Update.
  7. Start the update.

Use a stable Wi-Fi connection and stable power. Do not turn off the ignition or disconnect power during installation. Reboots and a GUI progress screen can be part of the normal process.

Source: FAQ notes; LM-Dash FAQ; confirmed LMCorse update sequence

Wi-Fi & updatesWill a normal firmware update erase my mileage?

The firmware update checklist states that a normal firmware update does not reset the odometer. A licensed mileage reset and a full online restore are separate procedures.

A full online restore overwrites data and can erase the odometer. Record the current mileage and contact LMCorse before a full restore.

Source: Firmware Update Checklist; Online Reset Checklist v3

Wi-Fi & updatesI get a network error before the update starts.

Use Connect to select and save the Wi-Fi network, then check whether network/IP information appears. Use a stable network.

The FAQ notes describe retrying the connection after the error and using the physical reset button. Only consider this after the connection attempt has failed and installation has not started. If installation is already in progress or the stage is unclear, contact LMCorse.

Source: FAQ notes; LM-Dash FAQ

Wi-Fi & updatesWhat should I check after a firmware update?

Confirm that the dashboard restarts normally, then check your layout, rev limits and gear display. The update checklist recommends checking the firmware version under Advanced → Firmware, or Info if available.

If speed calibration was previously adjusted, recheck its correction value under Advanced → SW Config → Calibration → Speed, where available on your firmware.

Source: Firmware Update Checklist

RecoveryThe screen is white, the percentage is stuck or I see “NO DATA”.

If this follows a failed GUI update and the screen has been stuck for more than 5 minutes, use the full Firmware restore tools procedure, Case 1.

First press the reset button in the hole to the left of the screen and wait a few minutes. eLMOS Build 28 introduced emergency GUI recovery. If nothing happens, use the FAT32 microSD recovery procedure detailed below.

Source: LMCorse firmware recovery instructions

RecoveryLM-Dash is stuck on “PLEASE WAIT”.

After a failed eLMOS update, first try the physical reset button to the left of the screen. If the problem persists, contact LMCorse before opening Advanced Restore Tools.

A full restore overwrites the activation code and data, including mileage. Record the mileage before proceeding and obtain LMCorse assistance.

See Firmware restore tools, Case 2.

Source: LMCorse firmware recovery instructions; Online Reset Checklist v3

RecoveryThe screen stays black or LM-Dash keeps restarting on USB power.

During GUI recovery, use a more powerful USB source, for example a 15 W charger, or connect the device to the vehicle. Then resume at step 5 of Case 1 and wait for loading to complete.

See Firmware restore tools for the complete sequence.

Source: LMCorse firmware recovery instructions

RecoveryHow does the online restore work?
Contact LMCorse first. This procedure overwrites the activation code and data, including the odometer. Record the current mileage before proceeding.
  1. Open Advanced Restore Tools using the link below.
  2. Enter the password provided by LMCorse.
  3. Install the drivers and follow the instructions on the restore page.
  4. Click Connect and select the USB port connected to LM-Dash.
  5. Select Install LMDash.
  6. Only after the preparation above, authorise overwriting the data.
  7. Keep power stable and wait for installation to finish.

Open Advanced Restore Tools →

Do not use Forced Reboot during updates.

Source: Online Reset Checklist v3; LMCorse firmware recovery instructions

Mileage & resetCan I change the odometer after initial setup?

The mileage is entered during first setup and is not an ordinary user-editable setting afterwards. If you made an entry error or need an authorised reset, contact LMCorse.

The reset procedure requires a code supplied by LMCorse. Keep a record of the correct mileage.

Source: LM-Dash FAQ; Odometer Reset Manual v2; FAQ notes

Mileage & resetHow do I use an odometer reset code from LMCorse?
  1. Power on LM-Dash, stop the car and engage the handbrake.
  2. From a screen other than Race, hold the steering-column button to open Setup.
  3. Go to Setting → Advanced → Firmware → LM-Dash Update → License Manager.
  4. Carefully enter the reset code supplied by LMCorse.
  5. Select Enter Code → Save and Exit.
  6. After reboot, enter the correct odometer value when prompted.

Record your mileage beforehand. The FAQ notes describe the code as single-use. Contact LMCorse if you do not have a code or if it is rejected.

Source: Odometer Reset Manual v2; FAQ notes

Gears & displayWhy is no gear shown when the car is stationary?

The FAQ states that the gear indicator works only while the vehicle is moving. No gear indication while parked is expected.

To enable it, go to Setup → Settings → Vehicle → Traction → Gearbox Type and select the correct gearbox. Ask LMCorse or your dealer if you are unsure which preset applies.

Source: LM-Dash FAQ

Gears & displayCan LM-Dash learn a custom gearbox?

Yes. Go to Setup → Settings → Vehicle → Traction → Gearbox Type and choose Custom. LM-Dash supports gear-ratio learning.

Learning requires the vehicle to be moving with the clutch released. Arrange a suitable controlled environment and follow LMCorse guidance; do not operate setup controls in traffic. Contact support for help completing the learning procedure for your vehicle.

Source: LM-Dash FAQ; FAQ notes

Gears & displayHow do I exit the Race / Race Pro / Pista layouts?
  1. Make sure your vehicle is stationary.
  2. Fully release the handbrake.
  3. Press and hold the original Trip/Reset button on the steering column.
  4. LM-Dash should switch to another dashboard layout.

Source: LMCorse support procedure

Gears & displayCan I change the layout and RPM warnings?

The main-features document describes five layouts, colour and brightness options, and configurable over-rev limits with visual warnings. Use the settings available on your installed firmware.

For a non-racing theme, a short press of the steering-column button changes the theme. Button behaviour differs in racing themes; see the button-controls answer.

Source: Main features; LM-Dash FAQ

ConnectionsCan I connect analogue sensors or a rear camera directly?

The FAQ notes state that the base LM-Dash cannot connect directly to analogue sensors or a rear camera.

The supplied documents describe external-sensor integration through expansion hardware, but refer to different modules and release plans. Contact LMCorse to confirm current hardware compatibility and availability before purchasing. The documents do not establish an available rear-camera solution.

Source: FAQ notes; Main features

ConnectionsDoes LM-Dash support aftermarket ECUs?

The main-features document lists compatibility with selected aftermarket ECUs, including Emerald K6. Compatibility depends on the exact vehicle, ECU and LM-Dash version. Contact LMCorse with those details before installation.

Source: Main features

Wi-Fi & updatesShould I enable Beta mode?

The FAQ notes include a Beta mode setting. Enable it only when LMCorse asks you to do so and provides instructions for your installed firmware.

For ordinary updates, use the standard firmware update procedure above.

Source: FAQ notes

Documentation

Your guides. Ready when you need them.

Read online or save a PDF for offline use.

If your browser opens a PDF instead of downloading it, use the viewer’s download button.

Online tools

Online reset & restore

Access the advanced eLMOS recovery tool. Check the troubleshooting answers before starting a full restore.

Contact LMCorse before proceeding. A full restore overwrites the activation code and data, including the odometer. Record your current mileage first.
Open online restore →
Firmware restore tools · Open recovery procedures

Choose the symptom below. Click a heading again to collapse it.

Case 1 · White screen, stuck percentage or “NO DATA”

Failed graphical interface update

Use this procedure if, after a failed GUI update, LM-Dash stays on a white screen for more than 5 minutes, with a stuck percentage or a “NO DATA” message.

  1. Reset the device by inserting a paper clip into the hole to the left of the screen and wait a few minutes. Emergency GUI recovery was introduced with eLMOS Build 28. If nothing happens, continue to step 2.
  2. Prepare a microSD card. Format it as FAT32 and copy LMDASH_INT.tft — download GUI file onto it.
  3. Switch off LM-Dash by removing the key. Insert the prepared microSD into the upper-right part of the dashboard. The dashboard must be removed from its shroud to access the slot.
  4. Power the device using a USB cable or by turning the key to ACC.
  5. Wait for loading to finish.
  6. Switch off LM-Dash by removing the key and/or disconnecting the USB cable.
  7. Remove the microSD card.
  8. Reconnect USB power or turn the key to ACC and wait for LM-Dash to start.
Black screen or repeated reboots on USB power? Use a more powerful USB source, such as a 15 W charger, or connect the device to the vehicle. Resume from step 5.
Case 2 · Stuck on “PLEASE WAIT”

Failed eLMOS base-software update

Use this procedure if LM-Dash remains on “PLEASE WAIT” after a failed software update.

  1. Try resetting the device using a paper clip in the reset hole to the left of the screen.
  2. If the problem persists, contact LMCorse before starting a restore. Then open Advanced Restore Tools and follow its instructions.
The activation code and data, including mileage, will be overwritten. Record the mileage and contact LMCorse before proceeding.

Still need help?

Email sales@lmcorse.com with your vehicle, LM-Dash version and the message shown on screen.